| Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. | |
|
+3bfurches V8Killer CrashMaster 7 posters |
Author | Message |
---|
CrashMaster
Posts : 190 Join date : 2011-12-05
| Subject: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Wed Jun 13, 2012 2:14 pm | |
| Need suggestions on a good/inexpensive place to get my driveshaft balenced. Also wondering if anyone has an OBD2 tuner that is willing to give up one of their limited tunes if I paid them handsomly . If not can anyone suggest where to have my PCM tuned on the lower cost side? I dont like PCM for less because of a bad experience with them on my firebird retune. Here is what I need done. The speedo recalibrated for the gears, speed limiter removed, firmer trans shifts, the egr/ cats/ evap emissions codes removed (in case I drop the cats in the future), and probably the abs light. I dont mean to sound like a cheap ass but Im a college kid with a very limited bank account. | |
|
| |
V8Killer
Posts : 1691 Join date : 2009-03-12 Age : 52 Location : Southern, NH
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Wed Jun 13, 2012 3:30 pm | |
| - CrashMaster wrote:
- Need suggestions on a good/inexpensive place to get my driveshaft balenced.
Also wondering if anyone has an OBD2 tuner that is willing to give up one of their limited tunes if I paid them handsomly . If not can anyone suggest where to have my PCM tuned on the lower cost side? I dont like PCM for less because of a bad experience with them on my firebird retune. Here is what I need done. The speedo recalibrated for the gears, speed limiter removed, firmer trans shifts, the egr/ cats/ evap emissions codes removed (in case I drop the cats in the future), and probably the abs light.
I dont mean to sound like a cheap ass but Im a college kid with a very limited bank account. I don't know where you are located, but both of these places are in Manchester NH I have used them both with awesome results! Gilbert Driveline Service & Supply Inc (603) 623-3061 340 Massabesic St Manchester, NH 03103 Jons Shafts & Stuff LLC (603) 627-4880 shaftsandstuff.com 347 Massabesic St, Manchester, NH 03103 | |
|
| |
bfurches
Posts : 1061 Join date : 2010-04-20 Age : 36 Location : Springfield, MA
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Wed Jun 13, 2012 3:43 pm | |
| I am in western ma. I have a good local machinist for balancing drive shafts, and if you want to purchase the credits through my HP Tuners I can dial the gears. | |
|
| |
IMPALADAKID Admin
Posts : 1525 Join date : 2009-01-17 Age : 55
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Wed Jun 13, 2012 7:13 pm | |
| I have had three tunes from PCMperformance.com and these guys rock! http://pcmperformance.com/programming.html | |
|
| |
8bud
Posts : 626 Join date : 2009-01-23 Age : 52 Location : Salem, NH
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Wed Jun 13, 2012 7:27 pm | |
| There is a place in North Reading I used a while back with good results. I'll find the name asap. It's directly across from Kittys restaurant, maybe someone knows the name?????
Update- North Shore Axle & Machine 126 Main St North Reading, MA 01864 978-664-2300 | |
|
| |
sdstick
Posts : 4292 Join date : 2009-03-20 Location : Revere, MA
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Wed Jun 13, 2012 8:40 pm | |
| Lived here forever....never knew they did that | |
|
| |
CrashMaster
Posts : 190 Join date : 2011-12-05
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Wed Jun 13, 2012 10:10 pm | |
| I may try the North Reading place Bill because it is close to my ride home for work. Could anyone tell me what the (ballpark) going rate is for a good balancing and how long it should take?
bfurches- Where is the western ma shop? Can you only dial in the gears? Or could you do the speedo limiter, shift firmness, ect? I am not sure what you mean by " purchase the credits through my HP Tuners " but if you can tune all or most of what ive listed above just hit me with a price!
impaladakid- If I cant find anyone local I will probably take that advice and thank you.
v8killer - I will try one of those if the north reading spot does not work out. Would you say one is better than the other?
Thanks again guys! Amazing help as always. | |
|
| |
1984twodoor
Posts : 4068 Join date : 2010-03-30 Age : 30 Location : Wilmington/Wakefield/Andover
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Thu Jun 14, 2012 12:50 am | |
| - sdstick wrote:
- Lived here forever....never knew they did that
C'mon you've got years on me and I even knew that! I've heard only good things BTW | |
|
| |
sdstick
Posts : 4292 Join date : 2009-03-20 Location : Revere, MA
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Thu Jun 14, 2012 5:54 am | |
| - 1984twodoor wrote:
- sdstick wrote:
- Lived here forever....never knew they did that
C'mon you've got years on me and I even knew that!
I've heard only good things BTW Never needed the service Wanted to stop in & see if they did rearend gears......but didnt Never saw a vehicle worth looking twice at there. #1 sign a place is good = gearhead hangout. | |
|
| |
V8Killer
Posts : 1691 Join date : 2009-03-12 Age : 52 Location : Southern, NH
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Thu Jun 14, 2012 10:48 am | |
| - sdstick wrote:
- #1 sign a place is good = gearhead hangout.
Huh, is that why I generate a crowd?? (I think everybody is just bored) | |
|
| |
sdstick
Posts : 4292 Join date : 2009-03-20 Location : Revere, MA
| |
| |
1984twodoor
Posts : 4068 Join date : 2010-03-30 Age : 30 Location : Wilmington/Wakefield/Andover
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Fri Jun 15, 2012 12:45 am | |
| - sdstick wrote:
- 1984twodoor wrote:
- sdstick wrote:
- Lived here forever....never knew they did that
C'mon you've got years on me and I even knew that!
I've heard only good things BTW Never needed the service Wanted to stop in & see if they did rearend gears......but didnt Never saw a vehicle worth looking twice at there. #1 sign a place is good = gearhead hangout. If I'm not mistaken it's Robert Sullivan who does it, He and all his buddys hang there, but they drive dump trucks and f-350s or the occasional v6 mustang 'vert I spend a lot of time there in the winter cleaning sanding trucks. | |
|
| |
sdstick
Posts : 4292 Join date : 2009-03-20 Location : Revere, MA
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. Fri Jun 15, 2012 8:40 am | |
| Good to know Thanks Matt | |
|
| |
Sponsored content
| Subject: Re: Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. | |
| |
|
| |
| Need suggestions on where to get my driveshaft balenced and was wondering if anyone could tune my pcm for my 4.11s once they are in. | |
|